arrow_back
Chapter 1: Introduction
Introduction to ENCOR
Examining Cisco Enterprise Network Architecture
Chapter 2: Understanding Cisco Switching Paths
Understanding Cisco Switching Paths
VLAN Labs and Trunking Issue
Trunking
Implementing Campus Lan Connectivity-1
Implementing Campus LAN Connectivity-2
Tuning STP, Configuring RSTP, BPTU Guard
RSTP
MSTP
Configuring NTP
Configuring OSPF- Multi Area
Configuring SNMP
Configuring VTP
Chapter 3: Routing Protocols
Implementing Layer 2 Port Aggregation
Implementing OSPF
Implementing OSPF Tuning and Multi-Area OSPF
Understanding EIGRP
EIGRP Configuration
Configuring EIGRP Authentication
Exploring EBGP
Configuring eBGP
Configuring iBGP
Configuring iBGP - Loopback Interface
Chapter 4: Policy Based Routing
Policy Based Routing
Implementing Infrastructure Security
Configure Control Plane Policing
Policy Based Routing
Chapter 5: Access Control
Implementing Secure Access Control
Configure Standard and Extended ACLs
Implementing Nat-1
Implement Nat (Lab) (2)
Configuring NAT - Static
Configuring NAT - Dynamic
Chapter 6: Multicast
Introducing Multicast Protocols
Implementing Network Redundancy - HSRP & VRRP
Configure and Verify Cisco IP SLAs
Configuring GRE Tunnel
Configuring IPSec
Configuring VRRP
Configuring VRF-Lite
Configuring IP SLA with HSRP
Chapter 7: AAA
Implement Local and Server-based AAA
Implementing Network Services - AAA Labs
Understanding Virtual Private Networks And Interfaces
Configuring AAA
Chapter 8: Wireless
Understanding Wireless Principles
Examining Wireless Ap Operation
Understanding Wireless Roaming and Location Services
Chapter 9: QoS
Introducing QoS
Configuring QoS
Chapter 10: Python
Python Installation
Fundamentals of Python-1.mp4
Chapter 11: Automation
Understanding the Working Principles of the Cisco SD-WAN Solution
Exploring Automation and Assurance Using Cisco DNA Center
Using Network Analysis Tools
Introducing Network Programmability Protocols - Telnet
netmiko
ENCOR Lab Guides
1.1.2 Lab - Implement Inter-VLAN Routing
2.1.2 Lab - Observe STP Topology Changes and Implement RSTP
3.1.2 Lab - Implement Advanced STP Modifications and Mechanisms
4.1.2 Lab - Implement MST
5.1.2 Lab - Implement VTP
5.1.3 Lab - Implement EtherChannel
5.1.4 Lab - Tuning EtherChannel
6.1.2 Lab - Investigate Static Routes
6.1.3 Lab - Implement VRF-Lite
8.1.2 Lab - Implement Single-Area OSPFv2
9.1.2 Lab - Implement Multi-Area OSPFv2
9.1.3 Lab - OSPFv2 Route Summarization and Filtering
10.1.2 Lab - Implement Multiarea OSPFv3
11.1.2 Lab - Implement eBGP for IPv4
11.1.3 Lab - Implement MP-BGP
12.1.3 Lab - Implement BGP Communities
12.1.2 Lab - Implement BGP Path Manipulation
15.1.2 Lab - Implement NTP
15.1.3 Lab - Implement HSRP
15.1.4 Lab - Implement VRRP
15.1.5 Lab - Implement GLBP
15.1.6 Lab - Implement NAT
16.1.2 Lab - Implement a GRE Tunnel
16.1.3 Lab - Implement IPsec Site-to-Site
16.1.4 Lab - Implement GRE over IPsec Site-to-Site VPNs
16.1.5 Lab - Implement IPsec VTI Site-to-Site VPNs
24.1.2 Lab - Use Connectivity Tests and Debug for Network Assurance
24.1.3 Lab - Implement SNMP and Syslog
24.1.4 Lab - Implement Flexible Netflow
24.1.5 Lab - Implement SPAN Technologies
24.1.6 Lab - Implement IP SLA
25.1.2 Lab - Install the CCNP Virtual Machine
26.1.2 Lab - Implement IPv4 ACLs
26.1.3 Lab - Configure Protections for Passwords and Terminal Lines
26.1.4 Lab - Configure Local and Server-Based AAA Authentication
26.1.6 Lab - Implement CoPP
28.1.2 Lab - Construct a Basic Python Script
28.1.3 Lab - Use the Netmiko Python Module to Configure a Router
28.1.4 Lab - Use NETCONF to Access a IOS XE Device
28.1.5 Lab - Use RESTCONF to Access an IOS XE Device
VLANs
OSPF - Area 0